Electronic energy meters' false readings almost six times higher than actual energy consumption

Electronic energy meters’ false readings almost six times higher than actual energy consumption
Test setup. Credit: University of Twente

Some electronic energy meters can give false readings that are up to 582% higher than actual energy consumption. This emerged from a study carried out by the University of Twente (UT), in collaboration with the Amsterdam University of Applied Sciences (AUAS). Professor Frank Leferink of the UT estimates that potentially inaccurate meters have been installed in the meter cabinets of at least 750,000 Dutch households. The is published in the scientific journal IEEE Electromagnetic Compatibility Magazine.

In the Netherlands, traditional (kWh) – the familiar meter with a rotating disc – are being increasingly replaced by electronic variants (which are also known as 'static energy meters'). One well-known variant of the latter is the 'smart meter.' The Dutch government wants in every household by 2020.

Actual consumption

For quite some time now, rumours have been rife about electronic energy meters that give excessively high readings in practice. This prompted Frank Leferink to investigate electronic meters, to see whether they can indeed give false readings. Together with co-workers Cees Keyer and Anton Melentjev from AUAS, he tested nine different electronic meters in this study. The meters in question were manufactured between 2004 and 2014. The meters were connected, via an electric switchboard, to a range of power-consuming appliances, such as energy saving light bulbs, heaters, LED bulbs and dimmers. The researchers then compared the actual consumption of the system with the electronic energy meter's readings.

582 percent

In the experiments (which were entirely reproducible), five of the nine meters gave readings that were much higher than the actual amount of power consumed. Indeed, in some setups, these were up to 582 percent higher. Conversely, two of the meters gave readings that were 30 percent lower than the actual amount of power consumed.

The greatest inaccuracies were seen when dimmers combined with energy saving light bulbs and LED bulbs were connected to the system. Cees Keyer (lecturer Electrical Engineering at the AUAS and PhD student at the UT), said, "These were laboratory tests, but we deliberately avoided using exceptional conditions. For example, a dimmer and 50 bulbs, while an average household has 47 bulbs."

The inaccurate readings are attributed to the energy meter's design, together with the increasing use of modern (often energy-efficient) switching devices. Here, the electricity being consumed no longer has a perfect waveform, instead it acquires an erratic pattern. The designers of modern energy meters have not made sufficient allowance for switching devices of this kind.

When they dismantled the energy meters tested, the researchers found that the ones associated with excessively high readings contained a 'Rogowski Coil' while those associated with excessively low readings contained a Hall Sensor. Frank Leferink (Professor of Electromagnetic Compatibility at the UT), says, "The energy meters we tested meet all the legal requirements and are certified. These requirements, however, have not made sufficient allowance for modern switching devices."

Any consumers who do not trust their energy meter can have it tested by an accredited inspection company. However, if this inspection shows that the meter is functioning properly, then the consumer will have to cover the costs involved. Yet the standardized test does not make allowance for waveform-contaminating power-consuming appliances. As a result, according to the researchers, it is an unsuitable method for detecting false meter readings. Prof. Leferink and Mr. Keyer advise any consumers who doubt their meter readings to contact their supplier, who then will pass the complaint on to the power grid operator.

Explore further

Smart-meter data could improve the performance and efficiency of national power grids

More information: Static Energy Meter Errors Caused by Conducted Electromagnetic Interference; Frank Leferink, Cees Keyer, Anton Melentjev; IEEE Electromagnetic Compatibility Magazine Volume 5, Quarter 4
Citation: Electronic energy meters' false readings almost six times higher than actual energy consumption (2017, March 6) retrieved 21 September 2019 from https://techxplore.com/news/2017-03-electronic-energy-meters-false-higher.html
This document is subject to copyright. Apart from any fair dealing for the purpose of private study or research, no part may be reproduced without the written permission. The content is provided for information purposes only.

Feedback to editors

User comments

Mar 06, 2017
Actually, switching power supplies and dimmers cause what's know as parasitic power use, which does not transfer energy towards the appliance. Instead, the extra current which does not transmit energy to the device dissapates more energy as heat in the wires and the distribution transformer and that is still actual power consumed from the point of view of the power utility.

Parasitic power happens when the voltage and current waveforms do not overlap, the disrepancy between is called the power factor. Good appliances are supposed to be power-factor corrected, but those are more expensive to make and they appear to use more energy.

The latter is because traditional power meters do not measure parasitic power, so things like compact fluorescent lightbulbs and LED bulbs seem to use a lot less energy than they actually do. A cheap manufacturer may omit the PFC and claim lower power consumption.

Mar 06, 2017
To those who may not be familiar with Eikka's terminology, Parasitic power is also known as the reactive component of power. The total power (reactance and resistive power) is measured in Volt-Amps.

What Eikka is pointing out is that these meters are doing a lousy job measuring reactive loads. This error goes heavily in favor of the power company.

The only downside to this test is that it focuses heavily on lighting and not nearly as much on the numerous wall transformers and computers. So the reality may be much worse than what this test shows.

Mar 06, 2017
"This error goes heavily in favor of the power company. "

Historically speaking, the power companies have taken the loss on reactive power because most household loads have been almost purely resistive - lightbulbs and heaters - it didn't make much difference to measure what didn't exist.

What you call "total power" (VA) is actually called Apparent power. It's not the true total power consumption of the system. The true power consumption is the product of I^2R (ohmic) losses caused by the current, plus the in-phase active power consumed by the appliance.

As I understand it, reactive power is not directly parasitic power - in an ideal circuit reactive power does no work. Simplistically, reactive power means a device uses more current to draw the same power out of the grid, and "reflects" the unused energy back to the source. This interchange causes extra transmission loss.

Please sign in to add a comment. Registration is free, and takes less than a minute. Read more