A new approach leads to better sodium ion battery

A new approach leads to better sodium ion battery
Outstanding electrochemical performance is achieved by using PTFSI as a novel additive, on account of suppressing the electrolyte-decomposing and better constructing the passivation-layer. Credit: Nano Research, Tsinghua University Press

Cheaper and far more abundant than lithium, sodium is increasingly appealing as a foundation for a next generation of high-voltage rechargeable batteries. Development of commercially viable sodium ion batteries lags significantly behind that of lithium batteries, which were widely adopted in the 1990s. But researchers worldwide aim to change that with the hope of eventually creating a more economical alternative to lithium. Advances in sodium ion battery performance could eventually lead to more widespread renewable energy adoption in power grids and drive down the cost of electric vehicles.

One of the major barriers to creating a viable ion battery has been finding a stable . Hard carbon currently is the most sodium ion battery common anode, but it comes with the disadvantage of interphasial instability—decomposed electrolytes build up on its surface, increasing the interphasial impedance, resulting in a sharp decline in discharge capacity.

A team of researchers in China tested N-Phenyl-bis(triflouromethanesufonomide) (PTFSI) as a proposed film-forming additive to hard carbon and found that it enhanced the interphasial stability, leading to a 52-percent increase in capacity retention of a sodium ion battery after 100 cycles. They published their findings in Nano Research.

"Sodium ion batteries have only gained renewed attention in recent years," said Lidan Xing, an professor in the School of Chemistry at South China Normal University and a co-author of the study. "Hard carbon is the most widely used anode material for sodium batteries, but its long cycle stability is not good enough to meet commercial and industrial application requirements. There has been little research on electrolyte matching with hard carbon anode materials."

The study found that adding PTFSI to the hard carbon anode improves the capacity retention of the hard carbon/Na half-cell they tested from 0 to 68 percent after 500 cycles. "This improvement is profound," Xing said.

Previous attempts at building a higher performing sodium ion battery have included adding a multi-functional nitrogen-doped hard carbon with an enlarged interlayer, and, in another case, developing a carbonized reconstructed lignin as a novel hard carbon anode. Experiments with other carbonate-based electrolytes for sodium ion batteries have been conducted using fluoroethylene carbonate, succinic anhydride, rubidium and cesium ions. None of those approaches came close to the improvement Xing and her colleagues achieved by adding a PTFSI film-forming electrolyte additive to the hard carbon anode.

"As a film-forming additive for the anode, PTFSI's reducing activity is as important as the properties of its decomposition products," Xing said. "For example, in this work, the structure of PTSFI is similar to that of a FSTI anion, and the structure and properties of their reduction products are also very similar. However, PTFSI is a molecule with a higher reducing activity that the FSTI anion. The former can improve the interphasial stability of hard carbon, but the latter cannot. Therefore, this work provides ideas for the design of hard carbon film forming additives."

The research team used coin cells to evaluate PTFSI as part of their new proposed electrolyte sodium ion system. They built the hard carbon anodes using thin copper foil cut to 12mm in diameter, coated and dried, then layered into half-cells with glass fiber separators and carbonated-based electrolyte. Batteries built both with and without their proposed PTFSI film-forming additive were charged and discharged up to 500 times. The authors concluded that significant performance gains presented with a 1-percent addition of PTFSI.

"We observed from this work that PTFSI can significantly improve long cycle performance of hard . Therefore, the next step is to evaluate its performance in large-capacity porch cells. If the results are similar to those of coin cells, we believe this additive could be used commercially in sodium ion batteries."

More information: Wenguang Zhang et al, Enhanced interphasial stability of hard carbon for sodium-ion battery via film-forming electrolyte additive, Nano Research (2022). DOI: 10.1007/s12274-022-4583-0

Journal information: Nano Research
Provided by Tsinghua University Press
Citation: A new approach leads to better sodium ion battery (2022, June 28) retrieved 18 July 2024 from https://techxplore.com/news/2022-06-approach-sodium-ion-battery.html
This document is subject to copyright. Apart from any fair dealing for the purpose of private study or research, no part may be reproduced without the written permission. The content is provided for information purposes only.

Explore further

Team creates anode-free Na batteries with high energy densities and long cycle lifetimes


Feedback to editors